Sort by:
ordered by relevance and dateSponsored Links
Electrical Motor
Marathon, Baldor, Leeson, Fincor Over 10,000 electric motors !
Ya wanna drag race? Pull your engine.
Forum | s2000.com | Aug 4, 2009
I found that guys personality to be quite abrasive. Seems funny that someone that is so concerned about the environment thinks using batteries is a eco friendly thing to do.
http://s2000.com/forums/racing-discussions/9318-ya-wanna-drag-race-pull-your.html
Xantrex Forums: 2 or 3 XWs' Idle current
The system: Off grid 2 XW6048s 2 XW60 SCP AGS 1450 Ah vented 3200 STC PV The master inverter is set to be on full time. The slave goes to --- when loads do not require it. The question: Why does the SCP show such high idle current (+/- 70 watts.
http://www.xantrex.com/forum/forum_posts.asp?TID=677&PID=2646
Cummins Filtration partners for nanofiber filtration systems
Forum | www.greentechforum.net | Jan 30, 2008
Green Technology Forum is a research and advising firm focusing on nanotechnology and biotechnology for growing green businesses.
Trinamic Discussion Groups :: View topic - Basic configuration of TMCM-090 and BB-3
The frequency of the LED changes. It was blinking on 10 seconds, off 10 and so forth. Now it is blinking at about 2 hz with a 50% duty cycle. What is the significance of this LED and the blink rate?
http://www.trinamic.com/ttdg/viewtopic.php?p=2665&sid=648f1a33936bdebf4e22d3ec7aaa0049
goldenmotor.com • View topic - amp rating for hub motor
I have been using the Model: PW-12H -- Wheelchair Hub Motor (brush/gear) for a short time, and have been going through fuses pretty rapidly. Can you tell me if this model can handle 16 amps? It seems rated for about 13.5, but I can't be sure.
http://www.goldenmotor.com/wheelforum/viewtopic.php?p=4&sid=9e4e3d3ad86b20c518690fb51284513e
Sponsored Links
Factory Ford Diagrams
82-08 Ford Online Factory Diagrams & Repair Information From ALLDATA
Mr. Whizard Technical Services
I also have a 2004 Impala, but with a crazy speedometer. Stepper motor again I assume. Should I get all of the stepper motors replaced to the other gauges (oil and Temp.) also? I heard they all go bad eventually. Post Response
http://www.mrwhizard.com/forum/FusionBoard.cfm?FN=view&TID=49
BCSC :: View topic - 33 EJB Earls court motor show
A 1966 Picture/Painting of 33 EJB on the Monte Carlo Rally. This is a large Picture that was used in the Earls court motor show. A collectors item.
http://www.bcsc.co.uk/forum/viewtopic.php?p=4&sid=81939680af3701d24bec201aef93f46b
imc DataWorks User Information Community • View topic - PWM 12V DC Motor Control
Is it possible to control a 12V dc motor using an IMC Cronos PL2? I was thinking of trying to progam a PWM signal in FAMOS to control the relay outputs on the imc...
http://www.imcdataworks.com/community/viewtopic.php?f=12&p=45&sid=3d4b08f2308a122a4e778f2239724b01
HVAC Compressor Runs but not the blower Motor - dslreports.com
HVAC Compressor Runs but not the blower Motor Last week the A/C system was on, and the Compressor was running but not the blower motor. The only way I could get it to turn on was by flipping the breaker for the blower off and turning it back and and things were fine for a week.
http://www.broadbandreports.com/forum/r20647229-HVAC-Compressor-Runs-but-not-the-blower-Motor
Digi International Support Forum
Hi, i need to control 2 motors via ethenert, and i don´t know how to do it. some know??
http://www.digi.com/support/forum/thread.jspa?messageID=11572

